DT7200 Intrinsically safe pressure transmitter

Product features

  • Measuring of the pressure of gases, vapours and liquids
  • Measuring of relative / absolute pressure, vacuum
  • Medium temperature: up to 140 °C
  • 32 measurement ranges between 0 and 25 bar
  • Intrinsically safe
  • 4-20 mA two-wire transmitter
  • G 1/2”A / M20 × 1.5 / G 3/4”A process connections
  • IP 65 protection

Product description

The DT7200 …Intrinsically safe pressure transmitters provide a 4-20 mA current signal in proportional to the pressure connected to their input. The transmitters are intrinsically safe devices, and they can be operated in a potentially explosive environment falling into the category Zone 0 and Zone 1.
The transmitters are available with 32 different measurement ranges, for the measuring of relative / absolute pressure and vacuum. Depending on the construction of the device, the temperature of the medium under measurement may vary between -25 °C and 140 °C, while the ambient temperature may be between -25 °C and 70 °C.
The material being in contact with the medium is KO36 steel; the sealing applied depends on the medium and the temperature of the medium, and it can be: Teflon (PTFE), Buna EP (EPDM), Viton (FKM), or Isolast 9503 (FFKM).
The transmitters are available with various threaded connections: G1/2”A / M20 x 1.5 manometer connection, and G 3/4” A front-membrane construction.

Technical specifications

Safety data:
The connection terminals of the supply voltages are isolated from each other, the isolation is in compliance with the standard EN 61010-1, taking into consideration the following:
Pollution level:2
Measurement category:II
Intrinsical safety data:
Certification:BKI 15 ATEX 0037 X
Protection marking:II 1/2 G EEx ia IIC T4/T3 (Class T3 in the case of more than 130 °C
temperatures of the medium)
Ui [V]Ii [mA]Pi [W]Ci [nF]Li [uH]
281000,737506
Input parameters:
Input signal:pressure
Ranges:see the table below
RANGESSpecial ranges that differ from the above are also available upon request.
[mbar] rel.[bar] rel.[bar] rel.[bar] rel.[bar] rel.[mbar] abs.[bar] abs.[bar] abs.
0-1000-1.000-10-1-0-1-6.000-4000-1.000-10
0-1600-1.600-16-1-1.00-1-100-6000-1.600-16
0-2500-2.500-25-1-1.60-1-160-2.500-25
0-4000-4.00-1-2.50-1-250-4.00
0-6000-6.00-1-4.000-6.00
Overdrive capacity:150%
Output parameters:
Output signal:DC current, proportional to the measured pressure
Range:4-20 mA
Accurary:0.25% (tipically)
Temperature-coefficient:200 ppm / °C (0-75 °C between), 300 ppm / °C (-20-90 °C betveen)
Supply-voltage effect:no
Response time:0.5 ms (10-90%)
Power supply:
Loop power supply voltage:12-28 VDC
Ambient conditions:
Operating temperature range:see the table below
TypeAmbient temperatureMedium temperature
DT7200 L-25 °C -25 °C
DT7200 M-25 °C -25 °C
DT7200 H-25 °C -25 °C
Relative humidity:90% (max., non-condensing)
Place of installation:potentially explosive area
Electromagnetic compatibility (EMC):
accordance with the standard EN 61326
Immunity:industrial area
Noise emission:Group 1, Class B
Data in general:
Housing:KO36 steel housing
Process connection:G1/2”A, M20 x 1.5 (manometer-connection),
G3/4”A (front-membrane connection)
Electrical connection:3-pole connector DIN43650/IP 65
Cross-section of the connected cable:2 × 0.25 mm2 (shielded cable)
Dimensions:DT7200 L: 36 × 154 mm(diameter × length)DT7200 M, DT7200 H: 36 × 203 mm (diameter × length)
Weight:DT7200 L: 0.3 kgDT7200 M, DT7200 H: 0.35 kg
Protection:IP 65
Materials being in contact with the medium
under measurement:
KO36 steel / Teflon (PTFE) / Buna EP (EPDM) / Viton (FKM) / Isolast
9503 (FFKM)
Detailed information see in operating instructions. The Manufacturer maintans the right to change the technical data!

Downloads

Leaflet of productOperating InstructionATEX certificate

Type selection and ordering

Login to see prices