The DT4260 … AC Current Meter enable 0-1 AAC / 0-5 AAC current ranges to be displayed on the control panel. Large 5 digit, 14.2 mm character height LED display make process value easily visible at a distance.
The displayed value is proportional to the True RMS value of the input current. The input current should be connected to the instrument’s shunt input through a current transformer.
The instrument is available with the following output options:
(* either analogue or communication option can be implemented at the same time)
Easy on-site configuration through the front panel membrane keypad is a major advantage of the microcontroller-based technology.
The configuration parameters: input range, current transformer ratio, signal filtering, output scaling, display refresh
rate, limit modes, limit values, etc. are stored in EEPROM. The settings are protected by a two-level password against unauthorised manipulation.
The instruments has two power supply versions: 24 VDC ±10% (DT4260 …) or 230 V AC/DC ±10% (DT4260 … PS).
The DT4260 … is housed in a DIN standard 96 × 48 mm ABS case with IP 65 protection from the front and IP 30 protection from the back side, for installation on the control panel.
| Safety data: | |
|---|---|
| The connection terminals of the supply voltages are isolated from each other, the isolation is in compliance with the standard EN 61010-1, taking into consideration the following: | |
| Pollution level: | 2 |
| Measurement category: | II |
| Input parameters: | |
| Input signal: | AC current, non isolated |
| Input resistance: | 0.01 ohm |
| Rectification: | True RMS |
| Measurement range: | 0-1 AAC / 0-5 AAC current |
| Overrange: | 2 × I (continous) |
| Sampling: | 12 measurement / sec. |
| Number of averaged samples: | 1 / 2 / 4 / 8 / 16 / 32 (selectable) |
| Error of displayed value: | < 0.2% @ Ta = 23 °C ±2 °C |
| Output parameters: | |
| Analogue output (optional): | |
| Output type: | 1 active or passive DC current (scalable) |
| Range: | 0-20 mA / 4-20 mA |
| Burden: | 600 ohm (max.) |
| Error: | < 0.03% @ Ta = 23 °C ±2 °C |
| Limit outputs (optional): | |
| Outputs: | 2 NO SPST relays |
| Contact rating: | 30 VDC, 3 ADC / 240 VAC, 3 AAC |
| Communication interface (optional): | |
| Type: | RS232 or RS485 (isolated) |
| Protocol: | Modbus RTU slave |
| Baud rate: | 300 / 600 / 1200 / 2400 / 4800 / 9600 Baud |
| Display: | |
| Display: | 5 digit, decimal point |
| Display unit: | 5 digit LED, 14.2 mm character height |
| Displayed value: | current multiplied by current transformer ratio |
| Manual controls: | |
| Manual controls: | 3 membrane push-buttons on the front cover |
| Power supply: | |
| Supply voltage: | 24 VDC ±10% (DT4260 ...) 230 V AC/DC ±10% (DT4260 ... PS) |
| Consumption: | 3.5 W / 3 VA |
| Ambient conditions: | |
| Operating temperature range: | 0-60 °C (-20 - +60 °C for customer request) |
| Relative humidity: | 90% (max., non condensing) |
| Place of installation: | cabinet |
| Electromagnetic compatibility (EMC) accordance with the standard EN 61326 |
|
| Immunity: | industrial area |
| Noise emission: | Group 1, Class B |
| General data: | |
| Housing: | panel instrument |
| Connection: | plug-in screw terminal / push-in direct connection |
| Connection cable: | 0.25-1.5 mm2 |
| Dimension: | 96 × 48 × 45 mm (width × height × depth) |
| Weight: | 0.15 kg |
| Protection: | IP 65 (front), IP 30 (rear) |
| Detailed information see in operating instructions. The Manufacturer maintans the right to change the technical data! | |
| Leaflet of product | Operating Instruction |
Analog output option:
RS232 communication interface option:
RS484 communication interface option:
RS485 bus topology:
